torsion spring

The utility model is composed of a front swing arm, a torsion bar, a back swing arm, a coil spring, etc.

该装置由前摆臂、扭杆、后摆臂和螺旋弹簧等部件构成。

A sensor is fixed to a frame of the loom through a connecting rod and a support, and the sensor is pressed on a licker-in roller through the connecting rod by a torsion spring.

其主要采用传感器通过连杆和支架固定在织机的机架上，扭簧通过连杆使传感器压在刺毛辊上。

In order to catch shock waves more efficiently, the technique of tension and torsion spring analogies was used to adjust the grids.

为更好地捕捉激波，对网格进行了自适应调整。

In this paper, the application and the mechanism principle of torsion spring overrun clutch are introduced.

介绍了扭簧式超越离合器的应用和机构原理.

The developed drill pipe valve used in gas drilling is made up of nipple, cushion, sealing parts, valve seat, pin bearing, cylindrical torsion spring and valve plate.

气体钻井过程中，常规的配套工具无法满足工艺要求，为此而研制的气体钻井用钻杆阀由钻杆阀短节、缓冲垫、密封部件、阀座、销轴、圆柱扭簧和阀板等组成。

The automobile uses three Basic types of spring : coil , leaf, and torsion Bar.

汽车使用的三种最基本的弹性元件为 螺旋弹簧, 钢板弹簧和扭杆弹簧.

The check valve shall utilize single torsion spring design to minimize pressure drop through the assembly.

止回阀应该采用单个扭力弹簧结构以减少通过总成的压降.

After a study on this hypothesized spring beam, a method for analyzing warping torsion on spot-welded thin-walled box section beam has been presented.

通过对这种具有假想弹簧的半闭口截面构件的研究，提出了一种分析点焊箱型截面薄壁构件的翘曲扭转的新方法。

In the most of works , the flexible joint is only predigested as a linear torsion spring.

但是在目前的研究中,通常仅仅简化柔性关节为线性扭转弹簧.

The blades are positioned on the large handle by a rotating shaft screw, and the pushing pawl and a pawl torsion spring are connected with the small handle through the pawl pin.

小手柄上通过棘爪销柱连接有推进棘爪及棘爪扭簧，推进棘爪受到棘爪扭簧的压力始终压制在刀片的齿上；

The check valves shall utilize a single torsion spring design to minimize pressure drop through the assembly.

这种止回阀应该采用单扭力弹簧结构来将通过总成的压降减到最小程度。

The paper studies the change of the equivalent torsion spring stiffness of the hydraulic steering device in the articulated vehicle as the geometrical layout of the hinge of the oil cylinder in the steering device alters, discusses how to improve the equivalent torsion stiffness and gets some conclusion.

对铰接式车辆液压转向机构当量扭转弹簧刚度随转向机构油缸铰点几何布局的变化关系进行了研究，探究如何提高此当量扭转刚度，得到一些结论。

The spring steel characteristics of one way low frequency long life torsion fatigue

弹簧钢单向扭转低频长寿命疲劳特性